Computational Study of the Influence of α/ß-Phase Ratio and Porosity on the Elastic Modulus of Ti-Based Alloy Foams.

This work aims to perform a computational analysis on the influence that microstructure and porosity have on the elastic modulus of Ti-6Al-4V foams used in biomedical applications with different α/ß-phase ratios. The work is divided into two analyses, first the influence that the α/ß-phase ratio has and second the effects that porosity and α/ß-phase ratio have on the elastic modulus. Two microstructures were analyzed: equiaxial α-phase grains + intergranular ß-phase (microstructure A) and equiaxial ß-phase grains + intergranular α-phase (microstructure B). The α/ß-phase ratio was variated from 10 to 90% and the porosity from 29 to 56%. The simulations of the elastic modulus were carried out using finite element analysis (FEA) using ANSYS software v19.3. The results were compared with experimental data reported by our group and those found in the literature. The ß-phase amount and porosity have a synergic effect on the elastic modulus, for example, when the foam has a porosity of 29 with 0% ß-phase, and it has an elastic modulus of ≈55 GPa, but when the ß-phase amount increases to 91%, the elastic modulus decreases as low as 38 GPa. The foams with 54% porosity have values smaller than 30 GPa for all the ß-phase amounts.

Recommendation on Orbiting Sample Cleanliness.

The National Aeronautics and Space Administration-European Space Agency (NASA-ESA) Mars Sample Return (MSR) campaign involves the collection of samples on Mars by the Perseverance (Mars 2020) rover and their return to Earth. To accomplish this, the Orbiting Sample container (OS) will be sent to Mars to accommodate the collected samples then launched from Mars and returned to Earth, where the samples will be removed for examination in the Sample Return Facility (SRF). Crucial to this entire sequence will be establishment of the required level of cleanliness inside the OS. In February 2021, the NASA Headquarters' Mars Sample Return Program and Office of Planetary Protection assembled an MSR OS Tiger Team (OSTT) to discuss the appropriate cleanliness level options of the interior of the OS. The team's remit was primarily focused on evaluating the trade-offs between Planetary Protection cleanliness levels 4a and 4b. These cleanliness levels are determined by the Committee on Space Research (COSPAR) planetary protection regulations, where 4a requires <300 bacterial spores/m2 and <3 x 105 bacterial spores on the spacecraft (in this case, the interior of the OS) and 4b mandates the more stringent requirement of <30 bacterial spores on the spacecraft. This report documents the consensus opinion submitted by the OSTT that recommended the interior of the OS be cleaned to a 4a requirement with any feasible added effort toward 4b. This report provides, as well, the rationale for that decision.

[Microbiological air quality in a Community Family Health Center of Talcahuano, Biobío Region, Chile]. / Calidad microbiológica del aire en un Centro Comunitario de Salud Familiar de Talcahuano, Región del Biobío, Chile.

BACKGROUND: Indoor air quality in health centers is essential to protect the health of people. In Chile, the Community Family Health Centers (CECOSF) are places with large attendance of people, favoring the dissemination of microorganisms, and there are no reports of the microbial air loading these health centers. AIM: To evaluate the microbiological indoor air quality in CECOSF-Centinela in Talcahuano, Biobío Region. METHODS: Air samples were taken in 6 rooms of the CECOSF, every 15 days between July 2018 and June 2019, with the MAS-100 NT equipment using trypticase and Sabouraud agars. Different morphotypes of bacteria and fungi were identified by PCR. RESULTS: The bacterial and fungal counts varied between 9.1 × 101 - 2.4 × 103 cfu/m3 and 10 - 1.5 × 102 cfu/m3, respectively. The air in the waiting room presented the highest counts, both for bacteria and fungi (P < 0.05). Staphylococcus, Enterococcus, Pseudomonas, Acinetobacter were identified, highlighting the species Staphylococcus aureus and Pseudomonas oryzihabitans, the latter described as a nosocomial pathogen. Among the fungi, Aspergillus, Meyerozyma and Rhodotorula were identified. CONCLUSION: The indoor air of the CECOSF-Centinela presents microorganisms of importance in human health. Therefore, it is necessary to formulate more regular monitoring programs for the control of air quality inside these health centers.

Study of the Influence of Sintering Atmosphere and Mechanical Activation on the Synthesis of Bulk Ti2AlN MAX Phase Obtained by Spark Plasma Sintering.

The influence of the mechanical activation process and sintering atmosphere on the microstructure and mechanical properties of bulk Ti2AlN has been investigated. The mixture of Ti and AlN powders was prepared in a 1:2 molar ratio, and a part of this powder mixture was subjected to a mechanical activation process under an argon atmosphere for 10 h using agate jars and balls as milling media. Then, the sintering and production of the Ti2AlN MAX phase were carried out by Spark Plasma Sintering under 30 MPa with vacuum or nitrogen atmospheres and at 1200 °C for 10 min. The crystal structure and microstructure of consolidated samples were characterized by X-ray Diffraction, Scanning Electron Microscopy, and Energy Dispersive X-ray Spectroscopy. The X-ray diffraction patterns were fitted using the Rietveld refinement for phase quantification and determined their most critical microstructural parameters. It was determined that by using nitrogen as a sintering atmosphere, Ti4AlN3 MAX phase and TiN were increased at the expense of the Ti2AlN. In the samples prepared from the activated powders, secondary phases like Ti5Si3 and Al2O3 were formed. However, the higher densification level presented in the sample produced by using both nitrogen atmosphere and MAP powder mixture is remarkable. Moreover, the high-purity Ti2AlN zone of the MAX-1200 presented a hardness of 4.3 GPa, and the rest of the samples exhibited slightly smaller hardness values (4.1, 4.0, and 4.2 GPa, respectively) which are matched with the higher porosity observed on the SEM images.

Fast Solution Synthesis of NiO-Gd0.1Ce0.9O1.95 Nanocomposite via Different Approach: Influence of Processing Parameters and Characterizations.

The synthesis of the nickel oxide-gadolinium doped ceria (NiO-GDC with 65:35 wt. %) nanocomposite powders with a stoichiometry of Gd0.1Ce0.9O1.95 was performed via fast solution combustion technique; using three different mixing methods: (i) CM (metal cations in an aqueous solution), (ii) HM (hand mortar), and (iii) BM (ball milling). The nanocomposite powders were calcined at 700 °C for 2 h and characterized by Transmission Electron Microscopy (TEM), X-ray fluorescence (XRF), and X-ray Diffraction XRD. The TEM and XRD analyses evidenced the well-dispersed NiO and GDC crystallites with the absence of secondary phases, respectively. Later, the calcined powders (NiO-GDC nanocomposites) were compacted and sintered at 1500 °C for 2 h. The microhardness of the sintered nanocomposites varies in accordance with the synthesis approach: a higher microhardness of 6.04 GPa was obtained for nanocomposites synthesized through CM, while 5.94 and 5.41 GPa were obtained for ball-milling and hand-mortar approach, respectively. Furthermore, it was observed that regardless of the long time-consuming ball-milling process with respect to the hand mortar, there was no significant improvement in the electrical properties.

Calidad microbiológica del aire en un Centro Comunitario de Salud Familiar de Talcahuano, Región del Biobío, Chile / Microbiological air quality in a Community Family Health Center of Talcahuano, Biobío Region, Chile

INTRODUCCIÓN: La calidad del aire en centros de salud es fundamental para resguardar la salud de las personas. En Chile, los Centros Comunitarios de Salud Familiar (CECOSF) son lugares de gran concurrencia de personas, favoreciendo la diseminación de microorganismos. OBJETIVO: Evaluar la calidad microbiológica del aire al interior del CECOSF-Centinela en Talcahuano, Región del Biobío. METODOLOGÍA: Se tomó muestras de aire en seis salas del CECOSF, quincenalmente, entre julio de 2018 y junio de 2019, con el equipo MAS-100 NT, empleando agar tripticasa y agar Sabouraud. Diferentes morfotipos de bacterias y hongos fueron identificados mediante RPC. RESULTADOS: Los recuentos de bacterias y hongos variaron entre 9,1 × 101 - 2,4 × 103 ufc/m3 y 10 - 1,5 × 102 ufc/m3, respectivamente. El aire de la sala de espera presentó los recuentos más altos, tanto para bacterias como hongos (P < 0,05). Se identificó Staphylococcus, Enterococcus, Pseudomonas, Acinetobacter, destacando las especies Staphylococcus aureus y Pseudomonas oryzihabitans, microrganismo este último, descrito actualmente como patógeno nosocomial. Entre los hongos se identificó Aspergillus, Meyerozyma y Rhodotorula. CONCLUSIÓN: Las muestras de aire del CECOSF-Centinela presentan microrganismos de importancia en salud humana. De ahí la necesidad de formular programas de monitoreo más regulares para controlar la calidad del aire al interior de estos establecimientos.

BACKGROUND: Indoor air quality in health centers is essential to protect the health of people. In Chile, the Community Family Health Centers (CECOSF) are places with large attendance of people, favoring the dissemination of microorganisms, and there are no reports of the microbial air loading these health centers. AIM: To evaluate the microbiological indoor air quality in CECOSF-Centinela in Talcahuano, Biobío Region. METHODS: Air samples were taken in 6 rooms of the CECOSF, every 15 days between July 2018 and June 2019, with the MAS-100 NT equipment using trypticase and Sabouraud agars. Different morphotypes of bacteria and fungi were identified by PCR. Results: The bacterial and fungal counts varied between 9.1 × 101 - 2.4 × 103 cfu/m3 and 10 - 1.5 × 102 cfu/m3, respectively. The air in the waiting room presented the highest counts, both for bacteria and fungi (P < 0.05). Staphylococcus, Enterococcus, Pseudomonas, Acinetobacter were identified, highlighting the species Staphylococcus aureus and Pseudomonas oryzihabitans, the latter described as a nosocomial pathogen. Among the fungi, Aspergillus, Meyerozyma and Rhodotorula were identified. CONCLUSION: The indoor air of the CECOSF-Centinela presents microorganisms of importance in human health. Therefore, it is necessary to formulate more regular monitoring programs for the control of air quality inside these health centers.

Synthesis and Characterization of a Nearly Single Bulk Ti2AlN MAX Phase Obtained from Ti/AlN Powder Mixture through Spark Plasma Sintering.

MAX phases are an advanced class of ceramics based on ternary carbides or nitrides that combine some of the ceramic and metallic properties, which make them potential candidate materials for many engineering applications under severe conditions. The present work reports the successful synthesis of nearly single bulk Ti2AlN MAX phase (>98% purity) through solid-state reaction and from a Ti and AlN powder mixture in a molar ratio of 2:1 as starting materials. The mixture of Ti and AlN powders was subjected to reactive spark plasma sintering (SPS) under 30 MPa at 1200 °C and 1300 °C for 10 min in a vacuum atmosphere. It was found that the massive formation of Al2O3 particles at the grain boundaries during sintering inhibits the development of the Ti2AlN MAX phase in the outer zone of the samples. The effect of sintering temperature on the microstructure and mechanical properties of the Ti2AlN MAX phase was investigated and discussed.

Effect of the Processing Parameters on the Porosity and Mechanical Behavior of Titanium Samples with Bimodal Microstructure Produced via Hot Pressing.

Commercially pure (c.p.) titanium grade IV with a bimodal microstructure is a promising material for biomedical implants. The influence of the processing parameters on the physical, microstructural, and mechanical properties was investigated. The bimodal microstructure was achieved from the blends of powder particles with different sizes, while the porous structure was obtained using the space-holder technique (50 vol.% of ammonium bicarbonate). Mechanically milled powders (10 and 20 h) were mixed in 50 wt.% or 75 wt.% with c.p. titanium. Four different mixtures of powders were precompacted via uniaxial cold pressing at 400 MPa. Then, the specimens were sintered at 750 °C via hot pressing in an argon gas atmosphere. The presence of a bimodal microstructure, comprised of small-grain regions separated by coarse-grain ones, was confirmed by optical and scanning electron microscopies. The samples with a bimodal microstructure exhibited an increase in the porosity compared with the commercially available pure Ti. In addition, the hardness was increased while the Young's modulus was decreased in the specimens with 75 wt.% of the milled powders (20 h).

Simultaneous measurement of δ2H, δ17O, and δ18O in H2O using a commercial cavity ringdown spectrometer.

We demonstrate that a commercial instrument that provides measurements of (18)O/(16)O and D/H ratios in water samples can be modified to also provide measurements of (17)O/(16)O. This additional capability and associated precision allows for the discernment between conventional mass-dependent processes, such as isotope exchange and evaporation and mass-independent processes that arise from non-equilibrium chemical and photochemical processes. We demonstrate this resolution by performing a series of experiments including evaporation and reservoir-mixing with (17)O enriched water samples followed by evaporation. The ability to simultaneously measure (16)O, (17)O, and (18)O abundances in water samples using the procedures described here should help to facilitate multi-isotopic studies of water (and other compounds) in astrochemical, geochemical, and biological studies.